Sigma -V series servo motor SGMPS.
Rated output: 200W (0.2KW).
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard).
Design sequence: IP55 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Corresponding to the RoHS instruction: in accordance with the RoHS directive SGD7S-2R8A00A Analog Voltage/Pulse Train References Manual SGD7S-2R8A00A HARDWARE MANUAL SGD7S-2R8A00A
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C SGD7S-2R8A00A Analog Voltage/Pulse Train References Manual SGD7S-2R8A00A HARDWARE MANUAL.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLarge capacity SGMVV type servo motor SGD7S-2R8A00A Analog Voltage/Pulse Train References Manual SGD7S-2R8A00A HARDWARE MANUAL.
Rated output: 22KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 800r/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: do not buy pieces.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen.





High performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: single phase AC100V.
Interface: MECHATROLINK-II communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Function: pressure feedback control function.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output functiion, can be smooth and high-precision control of rotary table SGD7S-2R8A00A Analog Voltage/Pulse Train References Manual SGD7S-2R8A00A HARDWARE MANUAL.
FT006 (fixed point through the output function): no need to pass through the upper device can bee set through the output (Chu Fa) SGD7S-2R8A00A Analog Voltage/Pulse Train References Manual SGD7S-2R8A00A HARDWARE MANUAL.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller.