Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC90V).
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGDV-R70A15B002FT003 MECHATROLINK-II Commands Manual SGDV-R70A15B002FT003 USER'S MANUAL SGDV-R70A15B002FT003
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen SGDV-R70A15B002FT003 MECHATROLINK-II Commands Manual SGDV-R70A15B002FT003 USER'S MANUAL.








Sigma -V series servo motor SGMSV.
Rated output: 2.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: no matching.
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake) SGDV-R70A15B002FT003 MECHATROLINK-II Commands Manual SGDV-R70A15B002FT003 USER'S MANUAL.
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationHigh performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC200V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Function: to support the absolute value of the system.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output functtion, can be smooth and high-precision control of rotary table SGDV-R70A15B002FT003 MECHATROLINK-II Commands Manual SGDV-R70A15B002FT003 USER'S MANUAL.
FT006 (fixed point through the output function): no need to pass through the upper device can bee set through the output (Chu Fa) SGDV-R70A15B002FT003 MECHATROLINK-II Commands Manual SGDV-R70A15B002FT003 USER'S MANUAL.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller.