LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGD7S-120A20A | Yaskawa Single axis servo driver SGD7S-120A20A
Yaskawa SGD7S-120A20A Manual And Instructions
SGD7S-120A20A datasheetPDF datasheet
SGD7S-120A20A Communications ReferencesHardware Manual
SGD7S-120A20A MECHATROLINK-III CommunicationsINSTRUCTION SHEET

Yaskawa SGD7S-120A20A Product information and technical parameters:
Brand: Yaskawa
Name: Single axis servo driver
Model: SGD7S-120A20A
Single axis servo driver SGD7S.
Maximum applicable motor capacity: 1.5kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type. ᥹఼
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified.
No need to write parameters in the device assembly site, can reduce the equipment delivery time.
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdown

Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 3.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: B.
Shaft end: straight shaft with screw key.
Optional parts: with DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain Yaskawa SGD7S-120A20A SGD7S-120A20A
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -V series servo motor SGMGV Yaskawa SGD7S-120A20A.
Rated output: 7.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake) Yaskawa SGD7S-120A20A.
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationSigma -V series servo motor SGMGV.
Rated output: 850W (0.85kw).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
HHeat resistance grade: F SGD7S-120A20A.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGD7S-120A20A.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation


...More relevant models >>>>