LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGD7S-330A20A002 | Yaskawa Single axis servo driver SGD7S-330A20A002
Yaskawa SGD7S-330A20A002 Manual And Instructions
SGD7S-330A20A002 datasheetPDF datasheet
SGD7S-330A20A002 Communications ReferencesInstruction Guide
SGD7S-330A20A002 MECHATROLINK-III CommunicationsINSTRUCTION SHEET

Yaskawa SGD7S-330A20A002 Product information and technical parameters:
Brand: Yaskawa
Name: Single axis servo driver
Model: SGD7S-330A20A002
Single axis servo driver SGD7S.
Maximum applicable motor capacity: 5.0kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type. ᥹఼
Design sequence: A.
Hardware options: paint.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified.
No need to write parameters in the device assembly site, can reduce the equipment delivery time.
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdown

Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: analog voltage, pulse sequence type (linear servo motor).
Matching (hardware): base mounting type (standard).
With the latest technology to pursue the use of convenience Yaskawa SGD7S-330A20A002.
The use of new non adjustment function, no need to adjust SGD7S-330A20A002
The vibration suppression function is also strengthened, and the load fluctuation can be effectively suppressed.
Greatly shorten the setting time.
Using engineering tool SigmaWin+ to set the guide function and the distribution confirmation function,
Can look at the picture simply to complete the start.
Achieve a high response 1kHz above Yaskawa SGD7S-330A20A002.
Equipped with a new advanced automatic tuning function.
Through the model tracking control, the positioning time is shortened,
And through the vibration suppression function, easy to achieve a smooth mechanical control.Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 3.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: B Yaskawa SGD7S-330A20A002.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: B.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control cirrcuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGD7S-330A20A002.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGD7S-330A20A002.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control


...More relevant models >>>>