LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGM7J-A5A7C6E | Yaskawa Rotary servo motor SGM7J-A5A7C6E
Yaskawa SGM7J-A5A7C6E Manual And Instructions
SGM7J-A5A7C6E datasheetPDF datasheet

Yaskawa SGM7J-A5A7C6E Product information and technical parameters:
Brand: Yaskawa
Name: Rotary servo motor
Model: SGM7J-A5A7C6E
No speed reducer in inertia, high speed servo motor type SGM7J (rated speed 3000r\/min).
Rated output: 50W.
Power supply voltage: AC200V.
Serial encoder: 24 bit absolute value type.
Design sequence: C.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with oil seal, with the brake (DC24V).
Cantilever state and moment of inertia.
After the change, can still maintain stable action.
Improvement of responsiveness.
Without adjustment, it can be achieved in the past about 2 times the response.
Improvement of stability.
The action is still stable for the presence of load fluctuations.
No gain adjustment.
Zero tuning time to ensure performance.
Protection system from the impact of temperature anomalies.
Servo unit and servo motor equipped with temperature sensor.
Monitor the temperature of the product directly through the sensor, as soon as possible to detect and prevent failure.
In addition, the temperature state of the system can be monitored by the machine controller, which is safe and secure

High performance, use the best type of servo unit (high performance).
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC200V.
Design sequence: A.
Hardware specifications: paint.
Interface: MECHATROLINK-III communication command type (linear servo motor).
Function: support 125 s communication cycle Yaskawa SGM7J-A5A7C6E.
High performance sigma shaped -V-EX series SGM7J-A5A7C6E
2 models of high performance servo unit.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control Yaskawa SGM7J-A5A7C6E. Sigma -V series servo motor SGMPS.
Rated output: 400W (0.4KW).
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: no matching.
Corresponding to the RoHS instruction: in accordance with the RoHS directive Yaskawa SGM7J-A5A7C6E.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 0.45kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGM7J-A5A7C6E.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGM7J-A5A7C6E.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control


...More relevant models >>>>