LK Automation Limited
Brand:
Yaskawa
SGMSH-20A2A3S | Yaskawa Super high power motor SGMSH-20A2A3S
Yaskawa SGMSH-20A2A3S Product information and technical parameters：
Brand: Yaskawa
Name: Super high power motor
Model: SGMSH-20A2A3S
Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 2.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with oil seal.
Ultra high power response series: the need for small inertia, high torque.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistor
Large capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 800r\/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: keep the brake (DC90V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties Yaskawa SGMSH-20A2A3S SGMSH-20A2A3S
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenDual axis servo drive SGD7W Yaskawa SGMSH-20A2A3S.
Maximum applicable motor capacity: 0.75kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type (Japanese production, interface is HMI connector).
Design sequence: A.
Hardware purchase: rack installation specifications.
Dual axis servo unit (200W x 2 axis to 1kW x 2 axis) Yaskawa SGMSH-20A2A3S.
Speed frequency response 1.6kHz.
Enhanced vibration suppression.
Gain adjustment without servo
YASKAWA created the "free adjustment function", the maximum load at 30 times the action does not produce vibration.
In addition, even if the action is changed, the action is stable.
Can be used in harsh environment and energy saving servo.
Can successfully build the best system in the worldLow inertia, high speed servo motor type SGM7A (rated speed 3000r\/min).
Rated output: 0.2kw.
Power supply voltage: AC200V.
Serial encoder: 24 bit absolute value type.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with hold brake (DC24V).
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 milllion 770 thousand \/rev pulse) SGMSH-20A2A3S.
The maximum torque of 350% (small capacity).
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
IIt is helpful to the servo performance of ultra high speed and ultra precision control SGMSH-20A2A3S. most
To limit the performance of the device to solve the problem
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 800r\/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: keep the brake (DC90V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties Yaskawa SGMSH-20A2A3S SGMSH-20A2A3S
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenDual axis servo drive SGD7W Yaskawa SGMSH-20A2A3S.
Maximum applicable motor capacity: 0.75kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type (Japanese production, interface is HMI connector).
Design sequence: A.
Hardware purchase: rack installation specifications.
Dual axis servo unit (200W x 2 axis to 1kW x 2 axis) Yaskawa SGMSH-20A2A3S.
Speed frequency response 1.6kHz.
Enhanced vibration suppression.
Gain adjustment without servo
YASKAWA created the "free adjustment function", the maximum load at 30 times the action does not produce vibration.
In addition, even if the action is changed, the action is stable.
Can be used in harsh environment and energy saving servo.
Can successfully build the best system in the worldLow inertia, high speed servo motor type SGM7A (rated speed 3000r\/min).
Rated output: 0.2kw.
Power supply voltage: AC200V.
Serial encoder: 24 bit absolute value type.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with hold brake (DC24V).
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 milllion 770 thousand \/rev pulse) SGMSH-20A2A3S.
The maximum torque of 350% (small capacity).
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
IIt is helpful to the servo performance of ultra high speed and ultra precision control SGMSH-20A2A3S. most
To limit the performance of the device to solve the problem
...More relevant models >>>>
Related download