LK Automation Limited
Brand:
Yaskawa
SGD7S-180A20A002 | Yaskawa Single axis servo driver SGD7S-180A20A002
Yaskawa SGD7S-180A20A002 Manual And Instructions
SGD7S-180A20A002 datasheetPDF datasheet
SGD7S-180A20A002 Communications ReferencesInstruction Guide
SGD7S-180A20A002 MECHATROLINK-III CommunicationsINSTRUCTION SHEET
Yaskawa SGD7S-180A20A002 Product information and technical parameters：
Brand: Yaskawa
Name: Single axis servo driver
Model: SGD7S-180A20A002
Single axis servo driver SGD7S.
Maximum applicable motor capacity: 2.0kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type. ఼
Design sequence: A.
Hardware options: paint.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified.
No need to write parameters in the device assembly site, can reduce the equipment delivery time.
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdown
...More relevant models >>>>
SGD7S-180A20A002 datasheetPDF datasheet
SGD7S-180A20A002 Communications ReferencesInstruction Guide
SGD7S-180A20A002 MECHATROLINK-III CommunicationsINSTRUCTION SHEET
Yaskawa SGD7S-180A20A002 Product information and technical parameters：
Brand: Yaskawa
Name: Single axis servo driver
Model: SGD7S-180A20A002
Single axis servo driver SGD7S.
Maximum applicable motor capacity: 2.0kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type. ఼
Design sequence: A.
Hardware options: paint.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified.
No need to write parameters in the device assembly site, can reduce the equipment delivery time.
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdown
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: single phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control Yaskawa SGD7S-180A20A002 SGD7S-180A20A002
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time Yaskawa SGD7S-180A20A002.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly Yaskawa SGD7S-180A20A002. Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: with hold brake (DC24V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSigma -V series servo motor SGMGV.
Rated output: 5.5kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heatt resistance grade: F SGD7S-180A20A002.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGD7S-180A20A002.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: single phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control Yaskawa SGD7S-180A20A002 SGD7S-180A20A002
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time Yaskawa SGD7S-180A20A002.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly Yaskawa SGD7S-180A20A002. Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: with hold brake (DC24V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSigma -V series servo motor SGMGV.
Rated output: 5.5kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heatt resistance grade: F SGD7S-180A20A002.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGD7S-180A20A002.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>