LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGDH-20AE | Yaskawa High performance servo driver SGDH-20AE
Yaskawa SGDH-20AE Manual And Instructions
SGDH-20AE datasheetPDF datasheet
SGDH-20AE AC Servodrive (400 V, 22 to 55 kW) Installation Guide
SGDH-20AE Hardware Manual

Yaskawa SGDH-20AE Product information and technical parameters:
Brand: Yaskawa
Name: High performance servo driver
Model: SGDH-20AE
Type: SGDH type drive.
Capacity: 2.0kw.
Voltage: three phase 200V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer.
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data.

Sigma -V series servo motor SGMGV.
Rated output: 5.5kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed) Yaskawa SGDH-20AE.
Variety is complete (300W ~ 15kW, with hold brake) SGDH-20AE
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above Yaskawa SGDH-20AE.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection Yaskawa SGDH-20AE.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor type SGMPH (speed: 3000r/min).
Power: 0.75kw.
Power supply voltage: three phase AC200V.
Serial encoder: 16 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with key.
Optional parts: no brake oil seal.
Partial flat series: the need to install the servo motor in a small space.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phaase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer SGDH-20AE.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a veryy seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated SGDH-20AE. 。


...More relevant models >>>>
Last one: Yaskawa SGDH-15DE
next one: Yaskawa SGDH-30AE