LK Automation Limited
Brand:
Yaskawa
SGDVR90A21B000000001 | Yaskawa Full closed loop servo system SGDVR90A21B000000001
Yaskawa SGDVR90A21B000000001 Product information and technical parameters：
Brand: Yaskawa
Name: Full closed loop servo system
Model: SGDVR90A21B000000001
Full closed loop module.
Maximum applicable motor capacity: 0.1kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Design sequence: B.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop module.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating).
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 2.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain Yaskawa SGDVR90A21B000000001 SGDVR90A21B000000001
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlType: SGDH type drive Yaskawa SGDVR90A21B000000001.
Capacity: 0.2kw.
Voltage: single phase 110V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor.
Test platform using on line test method Yaskawa SGDVR90A21B000000001.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer.
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Equipped with INDEXER functional type servo unit (kit type).
Maximum applicable motor capacity: 6.0kw.
Power supply voltage: three phase AC200V.
Interface: instruction selection and installation (linear servo motor).
Matching (hardware): shelf installation type + paint.
Matching (software): standard.
Matching (parameter): standard.
Optional module: INDEXER+ full closed loop module.
Simple.
By programming and serial programming, easy implementation of motion control.
Can also be installed through the Windows environment support tool (SigmaWin+) easy to start.
The I/O module can be connected with the upper controller simply.
Smart.
To support the operation of the main purpose of the positioning operation based on the program table.
The maximum number of programmablee positioning points to 256 points SGDVR90A21B000000001.
With external positioning, JOG speed table operation, the origin of reversion, rich features such as programmable signal output.
I/O points for the input: 19 points, output: 16 points.
Speedy. SGDVR90A21B000000001.
High speed and high precision positioning by combining with high performance V series.
Motion control can be realized without using motion controller.
Rated speed: 1500r\/min.
Power: 2.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain Yaskawa SGDVR90A21B000000001 SGDVR90A21B000000001
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlType: SGDH type drive Yaskawa SGDVR90A21B000000001.
Capacity: 0.2kw.
Voltage: single phase 110V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor.
Test platform using on line test method Yaskawa SGDVR90A21B000000001.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer.
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Equipped with INDEXER functional type servo unit (kit type).
Maximum applicable motor capacity: 6.0kw.
Power supply voltage: three phase AC200V.
Interface: instruction selection and installation (linear servo motor).
Matching (hardware): shelf installation type + paint.
Matching (software): standard.
Matching (parameter): standard.
Optional module: INDEXER+ full closed loop module.
Simple.
By programming and serial programming, easy implementation of motion control.
Can also be installed through the Windows environment support tool (SigmaWin+) easy to start.
The I/O module can be connected with the upper controller simply.
Smart.
To support the operation of the main purpose of the positioning operation based on the program table.
The maximum number of programmablee positioning points to 256 points SGDVR90A21B000000001.
With external positioning, JOG speed table operation, the origin of reversion, rich features such as programmable signal output.
I/O points for the input: 19 points, output: 16 points.
Speedy. SGDVR90A21B000000001.
High speed and high precision positioning by combining with high performance V series.
Motion control can be realized without using motion controller.
...More relevant models >>>>
Related download