LK Automation Limited
Brand:
Yaskawa
SGMAV-10ADABE | Yaskawa Ultra low inertia servo motor SGMAV-10ADABE
Yaskawa SGMAV-10ADABE Manual And Instructions
SGMAV-10ADABE Setup Rotational MotorCommand Manual
Yaskawa SGMAV-10ADABE Product information and technical parameters：
Brand: Yaskawa
Name: Ultra low inertia servo motor
Model: SGMAV-10ADABE
Sigma -V series servo motor SGMAV.
Rated output: 1.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMAV-10ADABE Setup Rotational MotorCommand Manual
Yaskawa SGMAV-10ADABE Product information and technical parameters：
Brand: Yaskawa
Name: Ultra low inertia servo motor
Model: SGMAV-10ADABE
Sigma -V series servo motor SGMAV.
Rated output: 1.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Servo motor SGMDH type.
Rated speed: 3000r\/min.
Power: 3.2kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, D24V brake.
Partial flat series: the need to install the servo motor in a small space Yaskawa SGMAV-10ADABE.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products SGMAV-10ADABE
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters Yaskawa SGMAV-10ADABE.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorType: SGDH type drive.
Capacity: 3.0kw.
Voltage: three phase 400V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load Yaskawa SGMAV-10ADABE.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer.
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo systemm is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data SGMAV-10ADABE. Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 1.3kw.
Power supply voltage: threee phase AC200V SGMAV-10ADABE.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: taper 1\/10, with parallel key.
Rated speed: 3000r\/min.
Power: 3.2kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, D24V brake.
Partial flat series: the need to install the servo motor in a small space Yaskawa SGMAV-10ADABE.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products SGMAV-10ADABE
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters Yaskawa SGMAV-10ADABE.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorType: SGDH type drive.
Capacity: 3.0kw.
Voltage: three phase 400V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load Yaskawa SGMAV-10ADABE.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer.
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo systemm is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data SGMAV-10ADABE. Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 1.3kw.
Power supply voltage: threee phase AC200V SGMAV-10ADABE.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: taper 1\/10, with parallel key.
...More relevant models >>>>