LK Automation Limited
Brand:
Yaskawa
SGMPS-08A2E6EE | Yaskawa Medium inertia flat type motor SGMPS-08A2E6EE
Yaskawa SGMPS-08A2E6EE Manual And Instructions
SGMPS-08A2E6EE Setup Rotational MotorProduct Manual
Yaskawa SGMPS-08A2E6EE Product information and technical parameters：
Brand: Yaskawa
Name: Medium inertia flat type motor
Model: SGMPS-08A2E6EE
Sigma -V series servo motor SGMPS.
Rated output: 750W (0.75kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMPS-08A2E6EE Setup Rotational MotorProduct Manual
Yaskawa SGMPS-08A2E6EE Product information and technical parameters：
Brand: Yaskawa
Name: Medium inertia flat type motor
Model: SGMPS-08A2E6EE
Sigma -V series servo motor SGMPS.
Rated output: 750W (0.75kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Servo driver SGD7S.
Maximum applicable motor capacity: 0.2kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-II communication command type.
Design sequence: A.
Hardware options: paint.
Performance excellence.
The performance and speed of the device can be improved.
Upgrade free adjustment function Yaskawa SGMPS-08A2E6EE.
Without adjusting the operation, no vibration can be achieved SGMPS-08A2E6EE
To ensure that the procedures and parameters of the previous product compatibility.
After replacement of the product, can easily improve the performance of the device.
Sigma -7 series has rich models and related products.
Customers can easily build the system.
From selection to maintenance, rich service content.
Especially when the servo system is in trouble,
Can immediately grasp the product information in the field Yaskawa SGMPS-08A2E6EE.
It is helpful to the servo performance of ultra high speed and ultra precision control.
Maximize the performance of the device, to solve the problemSigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Design sequence: A type Yaskawa SGMPS-08A2E6EE.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needss 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMPS-08A2E6EE.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMPS-08A2E6EE.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Maximum applicable motor capacity: 0.2kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-II communication command type.
Design sequence: A.
Hardware options: paint.
Performance excellence.
The performance and speed of the device can be improved.
Upgrade free adjustment function Yaskawa SGMPS-08A2E6EE.
Without adjusting the operation, no vibration can be achieved SGMPS-08A2E6EE
To ensure that the procedures and parameters of the previous product compatibility.
After replacement of the product, can easily improve the performance of the device.
Sigma -7 series has rich models and related products.
Customers can easily build the system.
From selection to maintenance, rich service content.
Especially when the servo system is in trouble,
Can immediately grasp the product information in the field Yaskawa SGMPS-08A2E6EE.
It is helpful to the servo performance of ultra high speed and ultra precision control.
Maximize the performance of the device, to solve the problemSigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Design sequence: A type Yaskawa SGMPS-08A2E6EE.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needss 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMPS-08A2E6EE.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMPS-08A2E6EE.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>