LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGMSV-30ADA2B | Yaskawa servo motor SGMSV-30ADA2B
Yaskawa SGMSV-30ADA2B Manual And Instructions
SGMSV-30ADA2B Setup Rotational MotorUSER'S MANUAL

Yaskawa SGMSV-30ADA2B Product information and technical parameters:
Brand: Yaskawa
Name: servo motor
Model: SGMSV-30ADA2B
Sigma -V series servo motor SGMSV.
Rated output: 3.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC90V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Equipped with DeviceNet communication function type servo unit (external power supply drive type)
Maximum applicable motor capacity: 15kw.
Power supply voltage: three phase AC200V.
Interface: instruction selection and installation (linear servo motor).
Optional (hardware): rack mounting type.
Matching (software): standard Yaskawa SGMSV-30ADA2B.
Matching (parameter): standard.
Optional modules: DeviceNet module (external power driver) + full closed loop module SGMSV-30ADA2B
Communication specifications for DeviceNet based on open field network.
The combination of the DeviceNet controller and the V can be used to implement motion control in a simple way.
Can make use of the city''s rich DeviceNet support software.
Can use the upper controller to manage the servo information Yaskawa SGMSV-30ADA2B.
Through the network from the host controller to monitor the running status of the servo drive, alarm information.
Using the upper controller to manage the servo information, which can improve the maintenance (shorten the debugging time, improve the efficiency of maintenance operations).
Save wiring, reduce the cost and improve the reliability.
Because the upper controller and the servo unit are connected through the communication network, the connection is greatly saved Yaskawa SGMSV-30ADA2B.
Built in rich positioning function.
Can be from the upper controller (PLC or computer) to carry out a variety of simple positioning action.
Equipped with simple positioning, continuous rotation, and return to the origin of continuous rotary motion positioning, running and other rich positioning function.Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC24V brake.
Ultra high power response series: the need for small inertia, high torque.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the inittial contact, can also be completed in a short time the best set SGMSV-30ADA2B.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regeneerative resistance connection terminals SGMSV-30ADA2B.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistor


...More relevant models >>>>